- how to remove the drip rail?
- essential tools
- Delrin/Plastic rod suppliers?
- Newbie Metal Work...
- Should I start over or keep working this patch?
- Beater Bag Questions
- Hammer Source?
- shaving door handles
- Want to avoid using polyester filler!
- Door damage
- Help Fine Tuning Required Please!
- Source for first set of hammers and dollys?
- Scratch made trunk floor...
- PLEASE HELP - Just a girl new to metalsmithing
- How to cure "tin can effect"?
- Dent repairs and slappers...
- What now?
- Not a bowl
- Starting my first sheetmetal project
- rearcing fender
- Moving an incorrectly located style edge?
- i need advice
- working with tubing
- Aluminum Ball Corners
- How Do You Planish Welds When You Can't Get to the Backside?
- How Would You Do This?
- controlled hacking (shaving door handles)
- newbie with a shrinking issue
- removing car gutter, best way????
- A few ?'s about woking my '36 Ford fenders..
- neewbie
- mig welding body panels-newbie
- another newbie question-Century mig
- Rear Quarter panel lip question
- Bonnet/hood top
- Intro & Project Thread
- How to make an acid-etched data plate?
- Rebuilding thread .. newbie sheetmetal work
- Tucking fork
- 1997 Mark VIII Custom
- tools to buy and what order?
- Project Ideas
- newbie with a few questions
- Rail Road Track
- Newbie needs help reprofileing wheel opening
- 1955 Chevy Truck Project
- Measure Twice, Bend Once
- Making the first bowl
- Testing your plug welds
- update on wheel openings
- recreating floor beads.
- wood slapper templates
- warpage with oxy-acetalyne
- my first patch panel
- Reshaped fender tips
- SlowRider's russian military truck
- "Z" Firewall rebuild
- 66 Galaxie front fender
- Newbie---WHERE DO I START ?
- Newbie Jumping into sheet metal
- 1973 Opel Kadett B
- Low spot raising hammering on dollie
- Radius forming with tuck shrinking
- Stretching with a hammer
- Making a 74 Norton Side Cover
- Windshield channel
- Embossed anvil on forge
- good work or crappy bull**** ?
- Aluminum Acoustic guitar
- Heat Effects on Panel.
- Rover P4 100 project
- 47 ford windshield repair
- Small dent removal techniques
- welding -losing the edge
- Dent removal advice please
- finishing the panel
- New to the forums with a question about Mustang hood
- Sheetmetal Dimples?
- butt welding patch panels
- tipping wheel
- How to make a very usefull tool,cheap!
- Passing the torch.......to my son
- english wheel questions?
- Tool Boxes
- An easy way to make your work more pro looking
- Tucking
- The Puck depth
- What type of raw stock to use?
- Guys How Would Make This With Sheet Metal?
- making a floor pan
- Add some "exclusive touch" on your work
- Hubcap Repair
- My first work
- Newbie needs to know how to fold this....
- Fab an aircleaner with use of a hammerform
- Oil Can, I Can't
- Need dolly with high crown in both axis
- Minor Dent and Wrinkle Repair
- Wing construction advice.
- learned a lesson today
- My '78 Camaro
- most important things to know for a new metal shaper
- Spot weld drills.
- Quality of basic tools
- Repairing dents, bodyline
- What to read and watch for a newbie
- Dent removal with hammer and dolly.
- shrunk welds help plz
- Wanted: Metal shaping exercises
- Reducing fender radius???
- Butt joining a repair panel on a slightly curved panel
- my first try at making matching bowls!
- new metal shaper here... sum pics of my first e-wheel try
- Newbie...Shrinkage problem
- metal shapeing dvds
- Lonnnng Time No Write
- starting off
- project GMC tail gate
- Newb looking for some help...
- Shrinking metal by hand
- my newbie stuff I made
- Removing waves from a welded panel
- My first two blocking hammers!
- Hello! metal work noob with a 86 gsxr
- Forming curved 911 flange for hood support. Comments?
- help a newb on a sphere, please.
- Hammering Strategies for Cymbals
- Chimney Top
- First attempt at rolling
- How do you remove this curl?
- Just a little van piece.
- kerosene's learning thread
- Oceanside Metal Meet
- John Deere Cab Fabrication
- seatpan and rear cowl for motorcycle
- Curved Z section
- How to start? Where to learn? Books to read?
- Putting arc in repro rocker panel(was "Using lead as a filler")
- Egli-Vincent gas tank
- Gas tank for practice
- Help shrinking tucks!
- How can I make these axle cans?
- Is zincor a worthwhile "investment"?
- stumped about stumps
- Need help finishing curve in panel
- How to get rid of a hump in a panel?
- Buck building and patern making
- Fender Swage the Gardiner way
- Metal shaping pliers
- Basics of hammer & dolly and planishing?
- Compound curve, English Wheel.
- Total Newbie
- Uber noob at it again! Tear drop fenders
- Compound Reverse Curve with hand tools?!
- getting started courses
- Need advice on which hammer and dolly I should buy first???
- New here. Need advice
- Advice on a wood stump
- Sleepy hollow? Stumped?
- Trying to make a bike!
- choosing a metalshaping hammer
- Power hammer
- Tips for fixing/filling small imperfections?
- Is this metal any good
- Aluminium and steel motorcycle tanks
- floorboard metal oil canning
- Fine wall art :-)
- New member, optimistic.
- making a new panel for a chop help
- Trans hump I thought I would share
- Fender Flares
- Advice on making a tank?
- Video # 9 dress a weld is out!
- repairing a roof of a 04 mustang...
- Forming over a solid wood buck
- Modifying Buick Fender
- 33ford inner apron
- pneumatic flanger
- E-wheel Weirdness
- Best way to make this channel
- Should I Try It?
- WM300 Power Wagon Fender
- Bench Vise
- I need advice
- Advise please
- Shrinking one end of a 4" tube
- Help with my wheel housings please
- Motorcycle muffler
- Help please
- Any Advice On Forming Body Trim?
- just bought a Longevity 200sx AC/DC welder
- sheet gauge qustion
- One last chance
- 20 ga for inner door structure?
- Maybe I Can Blame Bad Welding on Bad Eyesight
- Mothersday surprise and Ben's shop visit